The Long Range WiFi Bridge System is the best way to connect two locations to the same network wirelessly up to 3 miles away. This system is very simple to set up. It comes preconfigured and wired by C. Crane so there are no settings to adjust or software to install. Just attach the antennas (sold separately) to each half of the bridge, at each location, and plug them in. Use larger antennas like the Point-To-Point WiFi Antenna for long distances, or smaller antennas for shorter distances. Good line of sight without obstructions must be achieved between both antennas for best reception. LED lights on each bridging device make it easy to align your antennas with each other.
| Will it work for me? |
|---|
|
You will need to connect the first half of the WiFi Bridge, using the supplied 60" (5 foot) Ethernet cable, to an empty LAN port on your router. The Wireless Bridge then beams the encrypted Internet signal to your second location wirelessly. The second half of the system terminates with an Ethernet cable that provides Internet and network connectivity to one computer or other WiFi devices by using a WiFi router. You will need power at both locations to power the Bridge.
The signal between the two points of the WiFi Bridge System are heavily encrypted for security. The cost of the WiFi Bridge System is a fraction of the more expensive proprietary systems.
Up to 150 feet of regular low loss Cat-5e or Cat-6 Ethernet cable (not included) can be used to mount the antenna even further away on top of a tree or tower.
Please Note: C. Crane recommends the following antennas with the Long Range WiFi Bridge System: Point to Point WiFi Antenna and High-Gain 8dBi 2.4GHz Outdoor WiFi Antenna. It is possible to use another company's antennas that use the N-female type connection however we do not recommend antennas with a higher gain than what we offer due to FCC restrictions.
This kit is designed to be plugged into a router that is configured using Dynamic Host Configuration Protocol (DHCP) which is the standard factory configuration of most routers. An Internet Connection is also required.
| Kit Includes: | |
|---|---|
|
|
 | |
| Click To View Larger | |
| Note: Antennas are not included with this kit. They are sold separately | |
| Manual | Size | |
|---|---|---|
 | wifi bridge kit connection diagram | 168 KB |
| wifi bridge kit safety instructions | 811 KB |
| wifi bridge kit setup guide | 1.1 MB |
Yes, you can. You hop WiFi signals from the "client" house to another "client" house. To do this you will need an additional WiFi Bridge Kit and an additional router. You would connect the second bridge kit to the second router.
We do offer customized systems similar to our WiFi Bridge System such as a Custom Access Point (sending WiFi) and one or multiple Station to Router Systems (receiving WiFi). Please call our Customer Service at (800) 522-8863, Monday through Friday, 9am – 12pm and 1:15pm to 5pm. If you are unsure of your system needs, please fill out our Custom WiFi Request form and our specialist will contact you.
C. Crane recommends the following antennas with the WiFi Bridge System: Point to Point WiFi Antenna, 14dBi Indoor/Outdoor 2.4 GHz WiFi Antenna or High-Gain 8dBi 2.4GHz Outdoor WiFi Antenna. It is possible to use another company's antennas that use the N type connection however we do not recommend antennas with a higher gain than what we offer due to FCC restrictions.
| General Specifications | |
|---|---|
| Chipset: | Qualcomm™ QCA9531 with 650 MHz single-core MIPS 24Kc CPU |
| Flash/SDRAM: | 16 MB of SPI NOR flash |
| Networking Interface: | Fast Ethernet with ESD protection |
| WiFi Mode: | 802.11b/g/n |
| Standard POE Mode: | 802.3at/af Standard Module |
| Frequency: | 2.4 GHz |
| Security: | 504 bit WPA2 Encryption |
| Antenna Connector: | N-Male |
| Power Supply: | Input: 100~240 50-60Hz 1.2A Output: DC 56V (0.5A) |
| Power Method: | Passive Power over Ethernet |
| Operating Temperature: | -22° F to 158° F (-30° C to +70° C) |
| Bridge Device Weight: | 5.1 ounces |
| Bridge System Weight: | 7Lbs (not including antennas) |
| Ethernet Cable #1: | 50 FT, Category 6 Enhanced 550MHz, ANSI/TIA/EIA 568B.2, UTP Unshielded Twisted Pair, PVC Jacket, 24 AWG, Gold Plated Connectors |
| Ethernet Cable #2: | 5 FT, Category 5 Enhanced 350MHz, TIA/EIA 568B.2, UTP Unshielded Twisted Pair, PVC Jacket, 24 AWG, Gold Plated Connectors |
| Approvals | FCC ID 2AB8795312 |
| RoHS Compliance: | YES |
